CONFAST 5 8" x 10" Stainless Box 10 per Anchor New item Steel Wedge (10,per,Steel,Box),Anchor,5/8",Stainless,$113,10",CONFAST,www.quinceaneras.nyc,x,Wedge,Industrial Scientific , Fasteners , Anchors,/hipwort309631.html CONFAST 5 8" x 10" Stainless Box 10 per Anchor New item Steel Wedge $113 CONFAST 5/8" x 10" Stainless Steel Wedge Anchor (10 per Box) Industrial Scientific Fasteners Anchors $113 CONFAST 5/8" x 10" Stainless Steel Wedge Anchor (10 per Box) Industrial Scientific Fasteners Anchors (10,per,Steel,Box),Anchor,5/8",Stainless,$113,10",CONFAST,www.quinceaneras.nyc,x,Wedge,Industrial Scientific , Fasteners , Anchors,/hipwort309631.html

CONFAST 5 8

CONFAST 5/8" x 10" Stainless Steel Wedge Anchor (10 per Box)

$113

CONFAST 5/8" x 10" Stainless Steel Wedge Anchor (10 per Box)

|||

Product description

Applications
The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. Environment
The anchor is designed for use in a Wet environment.Hole Diameter/Bit Diameter
The anchor requires a 5/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor
The diameter of the anchor is 5/8".Length Anchor
The length of the anchor is 10"Thread Length
The length of the threads on the anchor is 4" in length.Minimum Embedment
The minimum anchor embedment into the concrete is 2-3/4". Therefore, the anchor must be installed so that a minimum of 2-3/4" of the anchor is embedded into the concrete.Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 6-5/8". This will ensure that the minimum embedment of 2-3/4" will be met.Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 5/8" diameter anchor requires the hole in the fixture to be 7/8".Torque Value
To be set properly in the concrete, the anchor must be torqued to between 75 - 90 ft./lbs.Spacing between Anchors
Each anchor must be spaced a minimum distance of 6-1/4" from each other when measured center to center.Edge Distance
It is very important not to install the anchor any closer than 3-1/8" from an unsupported edge of the concrete.

CONFAST 5/8" x 10" Stainless Steel Wedge Anchor (10 per Box)

Latest News and Articles

13.09.2021

What is a Signal Amplifier and How Does it Work?

Learn what is a signal amplifier, how does it work, its applications, benefits, and how they are used in the context of a data acquisition (DAQ) system.

Read more »
06.09.2021

Developing Advanced EV Battery Test Solutions

Learn more about progress in battery test technology and the SIRIUS XHS-PWR electric vehicle DAQ system which is based on advanced core technologies.

Read more »
06.09.2021

Visit us at Space Tech Expo 2021 in Long Beach, California

Meet the Dewesoft team at Booth 5044 from 6th till 8th of October and get the best overview of the test and measurement solutions for the space industry.

Read more »
30.08.2021

ADAS Standards and ADAS Safety Protocols

See the list of organizations and standards that take care of various aspects of vehicle safety, which necessarily involve ADAS and autonomous vehicles.

Read more »
30.08.2021

How Are ADAS Systems and Autonomous Vehicles Tested?

Learn how complex ADAS systems and autonomous vehicles are tested with vehicles and human drivers interacting on real roads under realistic conditions.

Read more »
30.08.2021

Types of ADAS Sensors in Use Today

Learn about key types of ADAS sensors used in today's autonomous vehicles. What are lidar, radar, sonar, cameras, and GNSS sensors? Read the entire guide.

Read more »

DewesoftX DAQ Software

Check our award-winning data acquisition software for test & measurement. Offers a complete feature set for data recording, data visualization, and data analysis. 

A Lot of Happy Customers

World-leading brands trust us and rely on our testing products and solutions. We serve over 5000 happy clients around the world.

I think I mentioned in previous emails how Dewesoft has mushroomed here, but even I didn't know how much. I was informed today that the data was being reviewed by up 50 to 60 different centers, along with NASA personnel as high as the manager of the entire Space Shuttle program.
It has been a long day, but before going home I wanted to say few things. Thank you from the bottom of my engineer heart and in the name of OneSubsea for what you did today! Yesterday at 10 PM I sent you an email asking for urgent help on a Saturday morning. 30 minutes later you replied you would come. This morning you were 5 people involved in resolving the issue. I have never experienced such customer service! Thanks again, customer service matters a lot to us, and today's response blew me away.
I have never encountered a company as competent as yours. Respect! You will always be encouraged and supported by me.
We recommend SIRIUS as a great unit to anyone that asks how we like it.
We absolutely enjoy using the Dewesoft data acquisition equipment and its software. I think of it as the Porsche 911 of data acquisition (my dream car/our dream test equipment).
Senior R&D boss shook the hand of the R&D manager: "You made the decision for the right instrument." With your instruments work makes fun again!
Again, thanks for all of the new features that are being included in Dewesoft X. It is already a fantastic product and deserves to become the Microsoft Word of data acquisition software.
Again, thanks for all the efforts on this project! I greatly appreciate everything you guys have provided to us.
I wanted to personally write to you and tell you how impressed I am with Dewesoft products. The whole Dewesoft team impressed me as extremely happy, smart, and dedicated. 
The setup and measurement process in the FRF module is really fascinating. Among the systems that I have seen, it is the absolutely most straight forward. Geometry and the measurement setup are available as files. It's a matter of minutes to have the final FRF's and the animation to get an impression of the vibrations. That's great!
The combination of software, hardware, and the Polygon plugin is really great. And on top of that, we can use it for so many things. This is just what we have been looking for!